Optimizing Coating Thickness for Enhanced Corrosion Resistance of Galvanized AISI 1045 Steel in Paddy Water
DOI:
https://doi.org/10.23960/jemit.531Keywords:
AISI 1045 steel, hot-dip galvanizing, corrosion rate, hardness, paddy water, ASTM G31, SEM-EDS, weight loss methodAbstract
AISI 1045 steel is extensively employed in agricultural machinery components, including shafts, gears, plowshares, and frames, owing to its favorable combination of tensile strength, toughness, and wear resistance. However, exposure to tropical paddy water containing chemical fertilizers, pesticides, chloride ions, and sulfate ions significantly accelerates corrosion, reducing equipment service life and increasing maintenance costs. This study investigated the relationship between galvanized coating thickness, produced through hot-dip galvanizing (HDG), and the corrosion rate, surface hardness, and microstructural characteristics of AISI 1045 steel under actual paddy water conditions.
Controlled experiments were conducted at a dipping temperature of 450 degrees C, with dipping times of 5, 7, 10, 15, and 20 minutes, alongside an uncoated control specimen. Coating thickness was measured using a digital thickness gauge. Corrosion rates were determined using the weight loss method in accordance with ASTM G31 after 30 days of immersion. Hardness was evaluated using the Rockwell HRB scale, and microstructural analyses were performed using SEM-EDS.
The results showed that coating thickness increased from 119 um at 5 minutes to 525 um at 20 minutes, following a parabolic relationship (d = 117.8 sqrt(tau), R2 = 0.998). The corrosion rate decreased from 18.05 mm/year for uncoated steel to 1.54 mm/year at 20 minutes, following an exponential decay model (CR = 18.05 exp(-0.0023d), R2 = 0.92), with protection efficiencies ranging from 48.6% to 91.5%. Hardness reached its highest values at 5 minutes (75.85 HRB) and 10 minutes (74.86 HRB). A linear relationship was observed for coating thicknesses up to 280 um (HRB = 88.2 - 0.150d, R2 = 0.99), followed by a sharp decrease at 15 minutes (63.68 HRB), attributed to microcracking. SEM-EDS analysis revealed Zn and ZnO layers, microcracks at dipping times of 10 minutes and longer, and Fe-Zn intermetallic phases.
The optimal dipping time was determined to be 10 +/- 2 minutes, corresponding to a coating thickness of 280 +/- 5 um. Under these conditions, the corrosion rate was 2.06 mm/year, the protection efficiency was 88.6%, and the hardness was 74.86 HRB. The coating also exhibited a smooth surface morphology with only minimal microcracking.
Downloads
References
Alhamdany, A. A., Alhamdany, A. A., & Kadhim, M. (2024). Characterization the effect of hot dip galvanize on the mechanical and the fatigue properties of the steel B500B. AIP Conference Proceedings. https://doi.org/10.1063/5.0205889
Alhamdany, A. A., Alhamdany, A. A., & Oudah, M. K. (2024). Numerical and experimental investigation of fatigue behavior of hot-dip galvanizing steel. AIP Conference Proceedings. https://doi.org/10.1063/5.0205890
Al-Nafai, I., Rzeszutek, K., Lyon, S., Jones, C., & Beaumont, D. (2025). How aluminium additions improve the performance of zinc-rich organic coatings. Materials and Corrosion, 76(1), 53-70. https://doi.org/10.1002/maco.202414529
Alweendo, S. T., Morita, M., Hasegawa, K., & Motoda, S. (2024). Effect of manufacturing-induced microscopic surface defects on crack initiation and fatigue mechanisms in hot-dip galvanized steel. Results in Materials, 23, Article 100609. https://doi.org/10.1016/j.rinma.2024.100609
Draz, U., Waseem, M., & Iqbal, T. (2025). Characterization and corrosion analysis of zinc coating by electrodeposition using acid chloride electrolyte solution. Results in Surfaces and Interfaces, 20, Article 100588. https://doi.org/10.1016/j.rsurfi.2025.100588
Fhaizal, M. A. (2021). Analysis of corrosion rate of carbon steel galvanized by weight loss method to thickness and micro structure of steel. VANOS Journal of Mechanical Engineering Education, 6(1). https://doi.org/10.30870/vanos.v6i1.10913
Fhaizal, M. A., Faizun, A., Wijaya, W., Sani, W., & Kristianti, L. (2024). Damage analysis of crank pin number 4 Sulzer 12 ZAV 40 S PLTD Ampenan Unit 7. Journal of Physics: Conference Series, 2928(1), Article 012012. https://doi.org/10.1088/1742-6596/2928/1/012012
Hamid, Z. A., Rehim, S. S. A. El, Shama, A. A., & Ebrahim, M. (2016). Improvement the corrosion resistance for the galvanized steel by adding Sn. Journal of Surface Engineered Materials and Advanced Technology, 6(2), 58-71. https://doi.org/10.4236/jsemat.2016.62006
He, C., Wang, Z., You, Y., Wang, X., Zhao, P., Yang, Z., & Zhou, L. (2025). Influence of soil variability on the corrosion of buried hot-dip galvanized steel. International Journal of Electrochemical Science, 20(1), Article 100889. https://doi.org/10.1016/j.ijoes.2024.100889
Jiang, Y., Zhang, H., Zhang, H., Shao, Y., Zhu, J., & Jin, X. (2025). Incorporating graphene-modified mica and conductive nickel particles for enhanced corrosion resistance in epoxy zinc-rich coatings. Frontiers in Chemistry, 13, Article 1544762. https://doi.org/10.3389/fchem.2025.1544762
Kania, H., Otmacic Curkovic, H., Kudlacek, J., Kapitanovic, A., Nackiewicz, J., Cerny, D., & Konopkin, G. (2024). The effect of Bi on the kinetics of growths, microstructure and corrosion resistance of hot-dip galvanized coatings. Materials, 17(22), Article 5604. https://doi.org/10.3390/ma17225604
Kosaba, T., Muto, I., Nishimoto, M., & Sugawara, Y. (2025). Electrochemical aspects of the roles of Na2MoO4 conversion treatment: Galvanic corrosion inhibition of AA5083 coupled to AISI 1045 carbon steel. Corrosion Communications, 20, 93-99. https://doi.org/10.1016/j.corcom.2024.06.003
Liu, Q., Cao, Y., Chen, S., Xu, X., Yao, M., Fang, J., Lei, K., & Liu, G. (2024). Hot-dip galvanizing process and the influence of metallic elements on composite coatings. Journal of Composites Science, 8(5), Article 160. https://doi.org/10.3390/jcs8050160
Lozrt, J., Votava, J., Kumbar, V., & Polcar, A. (2025). Analysis of corrosion-mechanical properties of electroplated and hot-dip zinc coatings on mechanically pre-treated steel substrate. Applied Sciences, 15(5), Article 2626. https://doi.org/10.3390/app15052626
Marek, A., Steinerova, V., Pokorny, P., Kania, H., & Berger, F. (2024). High-temperature Zn-5Al hot dip galvanizing of reinforcement steel. Coatings, 14(8), Article 959. https://doi.org/10.3390/coatings14080959
Pereira, R. F. da C., Oliveira, E. S. D. de, Lima, M. A. G. de A., & Brasil, S. L. D. C. (2015). Corrosion of galvanized steel under different soil moisture contents. Materials Research, 18(3), 563-568. https://doi.org/10.1590/1516-1439.341714
Pugalenthi, S., Devaraj, J., Maheswaran, C., & Benjamin, J. (2025). Optimization of Zn-Cr proportions for hybrid multilayer electroplating of AISI 1045 steel - Towards super-hydrophobicity and anti-corrosive nature. Journal of Adhesion Science and Technology, 39(3), 319-344. https://doi.org/10.1080/01694243.2024.2403683
Qi, C., Weinell, C. E., Dam-Johansen, K., & Wu, H. (2023). Assessment of anticorrosion performance of zinc-rich epoxy coatings added with zinc fibers for corrosion protection of steel. ACS Omega, 8(2), 1912-1922. https://doi.org/10.1021/acsomega.2c03738
Smak, M., Kubicek, J., Kala, J., Podany, K., & Vanerek, J. (2021). The influence of hot-dip galvanizing on the mechanical properties of high-strength steels. Materials, 14(18), Article 5219. https://doi.org/10.3390/ma14185219
Sudo, C., Aihara, K., Tsukamoto, T., & Nishimura, S. (1983). High strength and high fatigue limit zinc galvanized steel core wire for aluminum conductor steel reinforced (ACSR). Sumitomo Metals, 35(4), 63-72.
Voelkel, J., Kuhne, R., Bartsch, H., Feldmann, M., Oster, L., Sharma, R., Reisgen, U., & Pinger, T. (2023). Fatigue strength of hot-dip galvanized additively manufactured steel. Structures, 58, Article 105364. https://doi.org/10.1016/j.istruc.2023.105364
Xie, D.-M., Huang, K., Feng, X., & Wang, Y.-G. (2020). Improving the performance of zinc-rich coatings using conductive pigments and silane. Corrosion Engineering, Science and Technology, 55(7), 539-549. https://doi.org/10.1080/1478422X.2020.1759484
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026

This work is licensed under a Creative Commons Attribution 4.0 International License.







