Design and Build a Drum Collector Using a Stepper Motor Arduino Based on Nanofiber Spinning Machine (Electrospinning)

Wulan Oktaviani; Sri Wahyu Suciyati; Gurum Ahmad Pauzi; Junaidi Junaidi

doi:10.23960/jemit.v3i2.68

Authors

Wulan Oktaviani Department of Physics, University of Lampung, Bandar Lampung, Indonesia, 35141
Sri Wahyu Suciyati Department of Physics, University of Lampung, Bandar Lampung, Indonesia, 35141
Gurum Ahmad Pauzi Department of Physics, University of Lampung, Bandar Lampung, Indonesia, 35141
Junaidi Junaidi Department of Physics, University of Lampung, Bandar Lampung, Indonesia, 35141

DOI:

https://doi.org/10.23960/jemit.v3i2.68

Keywords:

Arduino, motor stepper, drum collector

Abstract

An Arduino-based stepper motor was used to create a nanofiber spinning machine. The hardware for this tool includes an Arduino Mega module, a 4x4 keypad, a TM1637 type seven-segment display, and L298N type stepper motor driver, a 17Hs4401 type stepper motor, a Pushbutton, and an ultrasonic sensor. The software utilized is the Arduino IDE, which is written in C. This tool's operating premise is that the Arduino processes input from the Keypad, and then the Stepper Motor Driver drives the stepper motor, which moves the collection drum up and down. The results of reading the tool will be presented in the seven segments in the form of RPM, altitude, and time. The tool has a height range of 1-10 cm, an RPM range of 10-100 RPM, and a time range of 1 minute to 1 hour. According to the test results, the tool has 99.8 percent accuracy at RPM, 99.92 percent accuracy at the time, and 97.89 percent accuracy at altitude.

Downloads

Download data is not yet available.

References

Agung. Nugroho Adi, 2010, Mekatronika, Graha Ilmu, Yogyakarta.

Alfith, 2015, Perancangan Traffic Light Berbasis Mikrokontroler Atmega16. Jurnal Momentum, Vol. 17 No. 1 Februari 2015. ISSN: 1693-752X.

Djuandi dan Feri. 2011. Pengenalan Arduino. Jakarta. Erlangga.

Herdiawan H.,Juliandri dan Nasir M., 2013, Pembuatan Karakterisasi Co-PDVF Nanofiber Komposit Menggunakan Metode Elektrospinning, Universitas Padjajaran, Bandung.

Judawisastra, Hermawan. Wiwin, Winiati. dan Ramadhianti, Prisa Annisa. 2012. Pembuatan Serat nano Kitosan tanpa Beads Melalui Penambahan PVA dan HDA. Jurnal Ilmiah Arena Tekstil Vol.27. No.2.

Nuryantini, A., Ekaputra. M., Munir. M., Suciati T., Khairurrijal. 2014, Sintesis NanoSerat Poli(Vinil Alkohol) dalam Bentuk Lembaran dengan Pemintal Elektrik Multi Nozel.Jurnal Pendidikan Fisika Indonesia, 10(2), (2014), 186-193.

Prakasa, Guntur Nanda. 2017. Prototipe Kunci Pintu Menggunakan Motor Stepper Berbasis Arduino Mega 2560 Dengan Perintah Suara Pada Android. Skripsi, Program sarjana Fakultas Teknik. Universitas Lampung. Bandar Lampung.

Riwayati I., 2007. Analisa Resiko Pengaruh Partikel Nano Terhadap Kesehatan Manusia. Momentum, Vol. 3 No. 2, Oktober 2007: 17 – 20.

Supegina, F., Munandar, A., 2014, Rancang Bangun Miniatur Otomatis Minuman Kaleng Berbasis Arduino Uno. Jurnal Teknologi Elektro, Universitas Mercu Buana. Vol 5 No. 3 September 2014.

Wahyudi T,dan Sugiyana Doni, 2011, Pembuatan Serat Nano Menggunakan Metode Elektrospinning. Arena Tekstil Vol. 26 No. 1 – Juni 2011:1-60.